Paint plant, machinery & formulation consultancy, India and worldwide

Two Component Waterproofing Manufacturing: PMC & PU Systems

How two-pack waterproofing systems work, how cementitious and polyurethane versions differ, and what a plant needs to pack them reliably.

01Introduction

In short: two component waterproofing combines a base and a hardener or powder and liquid at the point of use. The main families are polymer-modified cement slurries and polyurethane liquid membranes. Plant work is precise batching and kit packing, with strict control of mix ratio, moisture and pot life.

Two-pack products give higher performance than single-pack coatings but need discipline in production and in use. The customer must mix correctly and apply within pot life.

Plants that enter this category should be ready for more technical support and clear instructions.

02What Is Two Component Waterproofing?

Polymer-modified cementitious (PMC) systems pair a cement-based powder with an acrylic or SBR liquid. Polyurethane systems pair a polyol with an isocyanate and cure into a seamless elastic membrane.

Epoxy two-pack systems are used for specific applications such as tank linings and are covered under protective coatings.

Isocyanate-based products need trained handling. Moisture in raw materials or packs will spoil the product.

03Applications & End Uses

  • Bathroom, kitchen and balcony waterproofing
  • Terrace and podium slabs
  • Water tanks (approved grades)
  • Basements and planter boxes
  • Joint and detail waterproofing

04Types, Grades & Variants

SystemFeaturesTypical use
PMC two-packCement powder plus polymer liquidWet areas, basements, tanks
PU liquid membraneSeamless, highly elasticRoofs, balconies, exposed slabs
Epoxy-modified cementitiousStrong bond and chemical resistanceIndustrial floors, tanks
Acrylic two-packFlexible plus cementTerraces

05Raw Materials & Their Functions

Raw materialFunctionSelection note
Cement and graded fillers (PMC powder)BaseDry and consistent
Acrylic or SBR polymer dispersionLiquid componentSolids, alkali stability
Polyol resinPU baseLow moisture
Isocyanate hardenerCross-linkerStored dry
AdditivesFlow, adhesionSystem-specific
PigmentsColourDispersed in base

06Formulation Guidance

Formulations come from starting recipes tuned to your materials. Mix ratio and pot life must be proven by testing.

Component groupIndicative rangeWhy it matters
Component A (powder or polyol base)As per systemBase
Component B (liquid or hardener)As per ratioCure and flexibility
Ranges are indicative starting points for trials, not a ready formula. Final proportions depend on your raw materials, equipment, target cost and the standard you need to meet.

07Manufacturing Process

  1. Prepare Component ABlend powder or disperse polyol pastes.
  2. Prepare Component BPolymer liquid or hardener.
  3. Check ratioWeigh or measure into kits.
  4. Test mixed productPot life, flexibility, adhesion.
  5. Pack as kitsMatched kit sizes.
  6. LabelMix ratio, pot life, safety text.

08Machinery & Equipment

MachineRole in this product
Ribbon BlenderPMC powder blending
High Speed DisperserPU base dispersion
Paint Mixing & Storage TankLiquid components
Paint Filling MachineKit filling and labelling

09Plant Layout, Space & Utilities

  • Segregated PU area with dry atmosphere
  • Accurate weighing scales for kits
  • Clean-labelling and traceability by batch

10Quality Control & Testing

Test or checkWhat it tells youMethod or reference
Mix ratio verificationCorrect cureWeighing audit
Pot lifeApplication windowTimed sample
Elongation and tensileFlexibilityTensile test
Water impermeabilityWaterproofingWater column test
AdhesionBondPull-off

11Common Production Problems & Fixes

ProblemLikely causeWhat to do
Bubbles in PUMoistureDry materials
Cracks in PMCWrong flexibility classRe-formulate
Kit mismatchWrong fillingLabel and audit
Slow cureCold weatherAdjust catalyst and advise users
Poor bondSubstratePrimer and cleaning

12Capacity, Cost & Investment Factors

Two-pack costs more but sells at higher value:

  • Kit packaging and labelling
  • Raw material cost for polymers and isocyanates
  • Technical training for applicators
  • Warranty

13How IPCS Supports This Project

  • System selection (PMC or PU) for your market
  • Mix ratio validation
  • Kit packing process

Scope, deliverables and timelines are written into a quotation after we understand your products, capacity, site and budget. Machine details are indicative and are finalised against your product.

14Frequently Asked Questions

Which is better, PMC or PU?

PMC suits wet areas and below-grade slabs; PU suits exposed roofs and decks. Neither is universal.

What is pot life?

The working time after mixing.

Can I make PU waterproofing in a small plant?

Yes, if you can control moisture and handle isocyanate safely.

Does two-pack need a primer?

Often yes, depending on substrate and system.

How is quality checked?

By mix ratio audits, film tests and retained samples.

How can IPCS help me start two component waterproofing manufacturing?

IPCS confirms the product range and capacity, plans the process and machines, tunes the formulation with your raw materials, sets up the laboratory, trains your team and supports the first batches. The written quote states exactly what is included.

Get Technical Consultation

Tell us what you want to make. A paint technologist replies with next steps within one working day.

Your details are used only to reply to this enquiry. Direct line: +91 82104 79182.

Planning a paint or dry mix plant?Get Technical Consultation