Paint plant, machinery & formulation consultancy, India and worldwide

Sigma Mixer (Kneader) for Putty, Mastic & High-Viscosity Mixes

How a sigma blade kneader works, which products need it, and how to choose blade design, jacket and discharge.

01Introduction

In short: a sigma mixer is a horizontal kneader with two sigma-shaped blades rotating in a trough, folding and shearing very thick materials. It is used for putty paste, mastics, sealants and dough-like mixes that a disperser cannot handle. Trough tilting or screw discharge removes the mix.

When a mix is so thick that it holds its shape, the vortex-based disperser stops working. A sigma mixer kneads instead of stirring.

It is common in putty, mastic, sealant and some resin or rubber processing.

Sigma mixer kneader for putty and paste
IPCS sigma mixer.

02What Is Sigma Mixer?

Two sigma blades rotate toward each other at different speeds in a W-shaped trough. They fold the material over and squeeze it between blade and wall. Troughs may be jacketed for heating or cooling, and covers may be vented or vacuum tight.

Discharge is by tilting the trough or by a screw at the bottom.

03Working Principle

Differential speed between the two blades creates shear and folding, giving thorough mixing even for stiff materials.

  • Blades overlap closely for kneading
  • Trough tilts for discharge
  • Jacket for heating or cooling
  • Explosion-proof versions for solvent mastics

04Applications

  • Wall putty paste and acrylic fillers
  • Mastic and sealant
  • Putty for metal repair
  • Resin pastes and rubber compounds
  • Dough-like industrial mixes

05Types & Configurations

TypeFeaturesSuits
Tilting sigma mixerHydraulic or manual tiltMost common
Screw discharge sigma mixerBottom screwVery stiff or viscous mixes
Jacketed sigma mixerHeating or coolingTemperature-controlled mixes
Vacuum sigma mixerSealed with vacuumBubble-free mixes

06Key Selection Factors

FactorWhat to decideGuidance
Working volumeNet batchAbout 50 to 70 percent of trough volume
Viscosity and densityTorqueDefines motor power and gearbox
Blade speed ratioShear and kneadingStandard ratios
JacketTemperature controlThermic oil, steam or water
Material of constructionMS, SS 304 or SS 316Corrosion and cleanliness
DischargeTilt or screwMatch to material

07Where It Fits in the Process

  1. Load liquids and binderStart the blades.
  2. Add fillers in stagesAllow wetting.
  3. KneadUntil uniform.
  4. Add additivesFinal adjustments.
  5. Sample and testConsistency.
  6. DischargeTilt or screw out.

08Installation & Utility Requirements

  • Heavy foundation
  • Strong power supply
  • Hydraulic unit for tilting if used
  • Space for tilt motion and tub handling

09Safety & Operating Practice

  • Never reach into the trough; use interlocked covers
  • Lock-out for cleaning
  • Control temperature in jacketed units
  • Explosion-proof design for solvents

10Maintenance & Common Problems

ProblemLikely causeFix
Dead zones near trough endsWear or wrong blade clearanceAdjust clearance
Shaft seal leaksWearReplace seals, use gland care
Motor overloadMix too thickReduce batch or add liquid
Slow dischargeSticky materialUse screw discharge
HeatingFrictionJacket cooling

11How IPCS Supports Machinery Selection

  • Sizing for your thickest products
  • Material of construction and jacket advice
  • Comparison with twin shaft and planetary mixers

Machine details are indicative and are finalised against your product, batch size and site during quotation.

12Frequently Asked Questions

What is a sigma mixer used for?

For thick pastes such as putty, mastic and sealant.

How full should I load it?

Typically 50 to 70 percent of the trough volume.

Is a sigma mixer better than a planetary mixer?

Both are used for thick mixes; choice depends on viscosity, batch size and cleaning needs.

Can it mix solvent products?

With explosion-proof design.

How is it cleaned?

By tilting, scraping and washing with solvent or water as appropriate.

Get Machinery Details

Tell us what you want to make. A paint technologist replies with next steps within one working day.

Your details are used only to reply to this enquiry. Direct line: +91 82104 79182.

Planning a paint or dry mix plant?Get Technical Consultation