Paint plant, machinery & formulation consultancy, India and worldwide

Elastomeric Wall Coating Manufacturing: Formula, Testing & Machinery

How crack-bridging elastomeric wall coatings are formulated and made, and what to test before you sell them as waterproof or crack-resistant.

01Introduction

In short: elastomeric wall coating is a thick, flexible acrylic coating that stretches to bridge hairline cracks and resists water. It uses a low-Tg elastomeric binder, controlled filler and enough film thickness. It is made like emulsion paint but needs a heavier-duty disperser, careful testing and honest claims.

Elastomeric coatings sell where walls crack: coastal and monsoon regions, concrete facades and older buildings. They combine decoration with a degree of protection, which is why contractors value them.

The product is promising but easy to over-promise. A flexible film does not repair structural cracks or cure rising damp, and your marketing should say so.

02What Is Elastomeric Wall Coating?

The binder is an elastomeric acrylic with a low glass transition temperature, so the film stays flexible even at low temperatures. Filler loading is kept lower than in standard wall paint, and film thickness is higher, often applied in two coats.

Elongation, water vapour permeability and dirt pick-up are the main performance numbers. A good elastomeric coating balances flexibility with enough hardness to resist dirt.

03Applications & End Uses

  • Hairline crack bridging on exterior plaster and concrete
  • Wall facades in humid and coastal areas
  • Terrace parapets and exposed walls
  • Complement to waterproof treatments

04Types, Grades & Variants

VariantFeaturesNote
Smooth elastomericFlexible film with smooth finishCommon for wall facades
Textured elastomericFine texture hides patchy wallsNeeds a coarser filler
Roof elastomericHigher thickness, reflective pigmentsSee roof coating

05Raw Materials & Their Functions

Raw materialFunctionSelection note
Elastomeric acrylic emulsionFlexible binderLow Tg, high elongation, check dirt pick-up
Rutile TiO2Hiding, UV protectionExterior grade
Fine extenders (CaCO3, silicates)Bulk and costKeep PVC low to preserve elongation
Fibres (optional)Crack bridging aidDisperse well
BiocidesAlgae and fungus resistanceImportant in humid climates
Thickeners and dispersantsRheologyThick, high-build flow
CoalescentFilm formationAdjust to binder Tg

06Formulation Guidance

Elastomeric formulas are generally at a low PVC so the film remains flexible, often well below standard exterior paint. The binder share is therefore higher.

Component groupIndicative rangeWhy it matters
Water15% to 28%Carrier
Titanium dioxide8% to 16%Hiding
Extenders8% to 22%Kept low for flexibility
Elastomeric binder (as supplied)35% to 55%Main performance driver
Additives2% to 5%Thickener, biocide, dispersant
Ranges are indicative starting points for trials, not a ready formula. Final proportions depend on your raw materials, equipment, target cost and the standard you need to meet.

07Manufacturing Process

  1. SlurryWater, dispersant, wetting agent.
  2. DisperseTiO2 and extenders.
  3. Let downElastomeric binder at low speed.
  4. Add additivesThickener, biocides, coalescent.
  5. Adjust buildViscosity for high-build application.
  6. Test filmElongation and adhesion on films.
  7. FillFill into 20 litre pails or drums.

08Machinery & Equipment

MachineRole in this product
High Speed DisperserPremix and let-down
Twin Shaft DisperserHandles higher viscosity batches
Paint Mixing & Storage TankBatch and storage tanks
Paint Filtration MachineCoarse filtration for fibres or grit
Paint Filling MachinePail filling

09Plant Layout, Space & Utilities

  • Heavy-duty motors for high-viscosity mixing
  • Storage for binder drums at moderate temperature
  • Film casting and tensile testing area
  • Pails and lids that suit thick coatings

10Quality Control & Testing

Test or checkWhat it tells youMethod or reference
Elongation at breakCrack bridgingTensile test on free film
Water permeabilityWater resistanceWater column or absorption test
Adhesion on concreteBondPull-off test
Viscosity and buildApplied thicknessBrookfield
Dirt pick-up and weatheringLong-term lookWeather exposure
Low-temperature flexibilityBehaviour in cold climatesMandrel bend

11Common Production Problems & Fixes

ProblemLikely causeWhat to do
Surface tack and dirt pick-upBinder Tg too lowChoose a harder grade or add a hard resin
Cracking in a thick coatApplied too thick in one passSpecify two thinner coats
Poor adhesionDusty or weak substratePrime with a suitable primer
BlisteringTrapped moistureCheck wall moisture before coating
Viscosity too high for rollerOver-thickenedAdjust thickener

12Capacity, Cost & Investment Factors

Elastomeric products carry a premium price because binder content is high:

  • Elastomeric binder cost per kilogram of solids
  • Higher film build means more litres per square metre
  • Testing equipment for elongation
  • Labour training for applicators
  • Warranty exposure

13How IPCS Supports This Project

  • Formulation and binder screening with elongation targets
  • Claim wording that is honest and testable
  • Machine sizing for high-viscosity batches
  • Applicator guidance notes

Scope, deliverables and timelines are written into a quotation after we understand your products, capacity, site and budget. Machine details are indicative and are finalised against your product.

14Frequently Asked Questions

Can an elastomeric coating fix wall cracks?

It bridges fine hairline cracks and moves with minor substrate movement. It does not repair structural cracks or stop rising damp, which need repair of the cause.

How thick should elastomeric coating be applied?

Thickness depends on the product and system. Manufacturers usually specify two coats with a total dry film thickness stated in the data sheet.

Is elastomeric coating waterproof?

It resists liquid water but should not be sold as full waterproofing unless the product is tested for that use. Roof systems have separate requirements.

Why does elastomeric coating pick up dirt?

Soft, low-Tg films attract dust. Binder choice and formulation can reduce this.

Can I make it with a normal emulsion plant?

Mostly yes. You need a stronger mixer for higher viscosity and extra testing for elongation.

How can IPCS help me start elastomeric wall coating manufacturing?

IPCS confirms the product range and capacity, plans the process and machines, tunes the formulation with your raw materials, sets up the laboratory, trains your team and supports the first batches. The written quote states exactly what is included.

Get Technical Consultation

Tell us what you want to make. A paint technologist replies with next steps within one working day.

Your details are used only to reply to this enquiry. Direct line: +91 82104 79182.

Planning a paint or dry mix plant?Get Technical Consultation